MOXA NPort 5400 Serial Device Servers

 
 
 


NPort 5400 Series - General Device Servers

Features and Benefits
  •  User-friendly LCD panel for easy installation
  •  Adjustable termination and pull high/low resistors
  •  Socket modes: TCP server, TCP client, UDP
  •  Configure by Telnet, web browser, or Windows utility
  •  SNMP MIB-II for network management
  •  2 kV isolation protection for NPort 5430I/5450I/5450I-T
  •  -40 to 75°C operating temperature range (-T model)

NPort 5410NPort 5430NPort 5430i
NPort 5450
Serial InterfaceRS-232RS-422/485RS-422/485RS-232/422/485
Serial Interface ConnectorDB9 maleTerminal blockTerminal blockDB9 male
Serial Interface Isolation2 kV
Operating Temp.0 to 55°C0 to 55°C0 to 55°C0 to 55°C
Input Voltage12 to 48 VDC12 to 48 VDC12 to 48 VDC12 to 48 VDC

Introduction

NPort® 5400 device servers provide many useful features for serial-to-Ethernet applications, including an independent operation mode for each serial port, user-friendly LCD panel for easy installation, dual DC power inputs, and adjustable termination and pull high/low resistors.

Network Readiness for up to 4 Serial Devices

NPort® 5400 device servers can conveniently and transparently connect up to four serial devices to an Ethernet network, allowing you to network your existing serial devices with only basic configuration. Data transmission between the serial and Ethernet interfaces is bidirectional. By using NPort® device servers, you not only protect your current hardware investment, but also allow for future network expansion. You can both centralize the management of your serial devices and distribute management hosts over the network.

Independent Operation Mode for Each Serial Port

NPort® 5400 device servers can be used to connect different devices for remote data polling or event handling over a TCP/IP network. Each serial port on the NPort® 5400 operates independently to provide maximum versatility. For example, port 1 can operate in Driver mode, port 2 in TCP Server mode, and ports 3 and 4 in TCP Client mode.

User-friendly LCD Panel for Easy Installation

An LCD panel is built into the NPort® 5400’s top panel, with four buttons for data input, configuration, and operation mode selection. The LCD panel displays the server name, serial number, and IP address, and it can be used to enter or modify parameters such as IP address, netmask, and gateway. (The LCD panel is not available on wide-temperature models.)

Dual DC Power Inputs

NPort® 5400 device servers support dual power sources by providing both a DC terminal block input and a DC power jack input. Providing two types of power inputs gives users greater flexibility for use with different applications.

Adjustable Termination and Pull High/Low Resistors

The NPort 5400 Series provides adjustable termination and pull high/low resistors for RS-485 applications. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals, and the pull high/low resistors may need adjusting to maintain the integrity of the electrical signal. Since no set of resistor values is universally compatible with all environments, the NPort® 5400 has four sets of DIP switches on the bottom panel to set the termination and pull high/low resistor values.

Ethernet Interface

  • 10/100BaseT(X) Ports (RJ45 connector)

    1

  • Magnetic Isolation Protection

    1.5 kV (built-in)

Ethernet Software Features

  • Configuration Options

    Telnet Console, Windows Utility, Web Console (HTTP/HTTPS)

  • Management

    ARP, BOOTP, DHCP Client, DNS, HTTP, HTTPS, ICMP, IPv4, LLDP, Rtelnet, SMTP, SNMPv1/v2c, TCP/IP, Telnet, UDP

  • Filter

    IGMP v1/v2

  • Windows Real COM Drivers

    Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2/2016/2019 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded

  • Linux Real TTY Drivers

    Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x

  • Fixed TTY Drivers

    SCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X

  • Android API

    Android 3.1.x and later

  • Time Management

    SNTP

Serial Interface

  • Connector

    NPort 5410/5450/5450-T/5450I/5450I-T: DB9 male
    NPort 5430/5430I: Terminal block

  • No. of Ports

    4

  • Serial Standards

    NPort 5410: RS-232
    NPort 5430 Series: RS-422, RS-485
    NPort 5450 Series: RS-232, RS-422, RS-485

  • Operation Modes

    Disabled, Ethernet Modem, Pair Connection, Real COM, Reverse Telnet, TCP Client, TCP Server, UDP

  • Baudrate

    Supports standard baudrates (unit=bps): 50, 75, 110, 134, 150, 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 19200, 38400, 57600, 115200, 230.4k, 460.8k, 921.6k

  • Data Bits

    5, 6, 7, 8

  • Stop Bits

    1, 1.5, 2

  • Parity

    None, Even, Odd, Space, Mark

  • Flow Control

    RTS/CTS (RS-232 only), DTR/DSR (RS-232 only), XON/XOFF

  • Isolation

    2 kV isolation for NPort 5430I/5450I/5450I-T

  • Pull High/Low Resistor for RS-485

    1 kilo-ohm, 150 kilo-ohms

  • RS-485 Data Direction Control

    ADDC® (automatic data direction control)

  • Terminator for RS-485

    120 ohms

Serial Signals

  • RS-232

    TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND

  • RS-422

    Tx+, Tx-, Rx+, Rx-, GND

  • RS-485-4w

    Tx+, Tx-, Rx+, Rx-, GND

  • RS-485-2w

    Data+, Data-, GND

Power Parameters

  • Input Current

    NPort 5410/5450/5450-T: 350 mA @ 12 VDC
    NPort 5430: 320 mA @ 12 VDC
    NPort 5430I: 530 mA @ 12 VDC
    NPort 5450I/5450I-T: 554 mA @ 12 VDC

  • Input Voltage

    12 to 48 VDC

  • No. of Power Inputs

    2

  • Power Connector

    1 removable 3-contact terminal block(s)
    Power input jack

Reliability

  • Automatic Reboot Trigger

    Built-in WDT

  • Alert Tools

    Built-in buzzer and RTC (real-time clock)

Physical Characteristics

  • Housing

    Metal

  • Dimensions (with ears)

    181 x 103 x 33 mm (7.14 x 4.06 x 1.30 in)

  • Dimensions (without ears)

    158 x 103 x 33 mm (6.22 x 4.06 x 1.30 in)

  • Weight

    740 g (1.63 lb)

  • Interactive Interface

    LCD panel display (standard temp. models only)
    Push buttons for configuration (standard temp. models only)

  • Installation

    Desktop, DIN-rail mounting (with optional kit), Wall mounting

Environmental Limits

  • Operating Temperature

    Standard Models: 0 to 55°C (32 to 131°F)
    Wide Temp. Models: -40 to 75°C (-40 to 167°F)

  • Storage Temperature (package included)

    -40 to 75°C (-40 to 167°F)

  • Ambient Relative Humidity

    5 to 95% (non-condensing)

Standards and Certifications

  • EMC

    EN 55032/24

  • EMI

    CISPR 32, FCC Part 15B Class A

  • EMS

    IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
    IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
    IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV
    IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV
    IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
    IEC 61000-4-8 PFMF
    IEC 61000-4-11

  • Maritime

    DNV-GL (standard temp. models only)

  • Medical

    EN 60601-1-2 Class B, EN 55011 (NPort 5410/5450/5450I only)

  • Safety

    UL 60950-1

MTBF

  • Time

    NPort 5410: 310,331 hrs
    NPort 5430/5430I: 265,650 hrs
    NPort 5450/5450I: 206,903 hrs

  • Standards

    Telcordia (Bellcore) Standard TR/SR

Warranty

  • Warranty Period

    5 years