Optional 3,000 sheet High Capacity Feeder.
Benefits of the Infoprint 70 include:
- Advanced Controller Technology:
The IBM Infoprint 70 utilizes IBM's advanced controller technology
which supports printer resident web pages to view printer and job
status and to configure printer settings via a web browser. It comes
with standard integrated AFP/IPDS support. This allows the Infoprint 70
to take full advantage of the page level error detection and correction
capabilities of AFP. The Infoprint 70 can print even complex jobs at or
near rated speed.
- Excellent Print Quality:
New imaging technology enhances the appearance of graphics and
scanned images, with crisp halftones, improved solid area fill, and
enhanced gray scale capability. In addition, the printer's flexible
multiresolution support allows users to run existing 240 or 300 dpi
AFP/IPDS applications and print them at 600 dpi.
- Flexible Paper Handling:
Four paper trays are standard and provide a total of 3,150 sheets of
input capacity. An optional 3,000 sheet high capacity feeder is
available. This improves operator productivity by reducing the amount
of time spent loading paper. A large variety of standard and
nonstandard paper sizes and paper weights are supported.
- Standard Stapling Capacity:
The Infoprint 70 can staple sets of up to 50 sheets with the
standard main output stacker. It is possible to put two staples on the
side of each set or put one staple at the top or bottom corner. There
is also a standard 200 sheet capacity upper stacker without stapling
capability.
Key benefits of the Infoprint 70 include:
The Infoprint 70 uses an IBM high-performance controller with a 400
MHz PowerPC 750 processor, IBM printer co-processor, an internal 64 bit
data bus, and a 32 bit address bus running at 66 MHz. It has a standard
3.2 GB capacity or greater hard drive and a Peripheral Component
Interconnect (PCI) Bus for a Network Interface Card (NIC). The
Infoprint 70 controller has flash memory to support printer code
upgrade.
Included in the controller are:
- Memory
- 128 MB SDRAM Standard
- One memory slot that support additional 128 MB memory DIMM for a maximum of 256 MB
- Memory feature: 128 MB Memory DIMM (feature number 4390)
- AFP/IPDS
The Infoprint 70 uses the integrated IBM AFP/IPDS (Advanced Function Presentation/Intelligent Printer Data Stream) standard.
- Hard Drive
A hard drive (3.2 GB or greater) comes standard on the Infoprint 70.
DBCS fonts and SEMEA fonts come stored on the hard drive. Fonts and
macros may be individually deleted from the hard drive.
- Minimum Memory requirements
The Infoprint 70 comes standard with 128 MB of memory. This
configuration can support simplex or duplex printing, using AFP/IPDS
with SBCS or DBCS. However, additional memory MAY be required to
achieve optimal performance.
Printer System Attachment Interfaces
Print Quality
The Infoprint 70 offers high quality print resolution of 600 x 600
DPI. It supports up to 32 levels of gray for IOCA images. The printer
will convert 240/300 DPI AFP/IPDS to 600 DPI in enhanced print mode.
The Infoprint 70 uses a new imaging technology which prints single dot lines clearly and produces excellent solid area fill.
Paper Handling
The maximum monthly usage for the Infoprint 70 is up to 400,000
impressions. IBM does not recommend printing this monthly maximum on a
consistent basis.
- Paper Capacities
Input capacities in sheets:
Standard Standard Standard Standard Optional Total
Tray 1 Tray 2 Tray 3 Aux.Tray HCF(1) Capacity
-------- -------- -------- -------- -------- --------
2000 500 500 150 3150
3000 6150
Note: (1) High Capacity Feeder
- Output capacities in sheets:
Standard Standard Total
Main Stacker Upper Stacker Capacity
------------ ------------- --------
2000 200 2200
The
engine first print out time is approximately 10 seconds for simplex
printing (Ledger SEF, Letter LEF), and approximately 15 seconds for
duplex printing (Ledger SEF, Letter LEF). First print-out time is the time from when the printer receives a
start printing signal in "READY" state until one sheet of paper is
printed and delivered.
The printer reaches the "READY" state within 240 seconds of power on.
The maximum rated engine speeds are as follows (Impressions Per Minute).
Tray 1,2,3 Aux. Tray
---------------------- ----------
Paper Size Simplex Duplex Simplex
---------- ---------- ---------- ----------
A5 SEF (1) 70 70 63
B5-JIS LEF 70 70 63
A4 LEF 70 70 63
A4 SEF 40 40 31
B4-JIS SEF 40 40 31
A3 SEF 35 35 31
Letter (8.5" x 11") LEF 70 70 63
Letter (8.5" x 11") SEF 40 40 31
Statement(5.5x8.5") SEF 70 70 63
Executive(10.5x7.25")LEF 70 70 63
Tab stock(9" x 11") LEF 40 N/A 31
8.5" x 12.4" SEF 40 40 31
Legal 13"(8.5x13") SEF 40 40 31
Legal 14"(8.5x14") SEF 40 40 31
Ledger(11" x 17") SEF 35 35 31
12" x 18" SEF 33 33 31
Custom N/A N/A 31-63
Note: Heavy media type reduces printing speed.
Note: SEF = short edge feed, LEF = long edge feed
Note: (1) Not supported in tray 1.
The maximum monthly usage of Infoprint 70 is up to 400,000
impressions. IBM does not recommend printing to this monthly maximum on
a consistent basis.
The following paper sizes/media types are supported in the input trays and output stackers (see note 1):
Tray Trays Aux. Opt. Main Main Upper
1 2,3 Tray HCF Stack. Stack. Stack.
Paper Size (2) (3) (4) (5) (Staple)
------------------------ ---- ----- ---- ---- ----- ------- ------
A5 SEF No Yes Yes No Yes No Yes
(148x210mm, 5.83x8.27")
B5-JIS LEF Yes Yes Yes No Yes Yes Yes
(182x257mm, 7.16x10.12")
A4 LEF Yes Yes Yes Yes Yes Yes Yes
(210x297mm, 8.27x11.69")
A4 SEF Yes Yes Yes No Yes Yes Yes
(210x297mm, 8.27x11.69")
B4-JIS SEF Yes Yes Yes No Yes Yes Yes
(257x364mm, 10.12x14.33")
A3 SEF Yes Yes Yes No Yes Yes Yes
(297x420mm, 11.69x16.54")
Letter LEF Yes Yes Yes Yes Yes Yes Yes
(215.9x279.4mm, 8.5x11")
Letter SEF Yes Yes Yes No Yes Yes Yes
(215.9x279.4mm, 8.5x11")
8.5x12.4" SEF Yes Yes Yes No Yes Yes Yes
(215.9x315mm, 8.5x12.4")
Folio SEF Yes Yes Yes No Yes Yes Yes
(215.9x330.2mm, 8.5x13")
Legal 14" SEF Yes Yes Yes No Yes Yes Yes
(215.9x355.6mm, 8.5x14")
Ledger SEF Yes Yes Yes No Yes Yes Yes
(279.4x431.8mm, 11x17")
12x18" SEF Yes Yes Yes No Yes No No
(304.8x457.2mm, 12x18")
Statement SEF No Yes Yes No Yes No Yes
(139.7x215.9mm, 5.5x8.5")
Executive LEF No Yes Yes No Yes No Yes
(266.7x184.2mm, 10.5x7.25")
Tab Stock LEF Yes Yes Yes No Yes Yes Yes
(9x11")
Custom No No Yes No Yes No Yes
Note: (1) Some print media, although they may conform to size
and weight specifications, may still not perform to your expectations.
Print quality, jam rates, fuser life and output stacking can be
affected by the printing environment (temperature and humidity) and
characteristics of the paper (structure, moisture content, smoothness
or thickness); refer to IBM Document G544-3915 for paper
specifications. IBM STRONGLY RECOMMENDS YOU TEST SMALL AMOUNTS OF PRINT
MEDIA USING YOUR PRINTING APPLICATION BEFORE PURCHASING LARGE
QUANTITIES OF THE MEDIA OR RUNNING LARGE PRINT VOLUMES.
Note: (2) 208 mm maximum stack height. Up to 2000 sheets copier/xerographic paper (20lb/75gsm).
Note: (3) 50 mm maximum stack height. Up to 500 sheets of copier/xerographic paper (20lb/75gsm).
Note: (4) 15 mm maximum stack height. Up to 150 sheets of copier/xerographic paper (20lb/75gsm).
Note: (5) 340 mm maximum stack height. Up to 3000 sheets of copier/xerographic paper (20lb/75gsm).
Both output stackers support face-down stacking only.
Duplex printing is supported standard. See media type table for
media types supported. Duplex printing is not supported with Auxiliary
Tray.
Stapling is supported standard with Main Stacker. See paper size
table for paper sizes supported. Three stapling positions are supported
and maximum of 50 sheets can be stapled at one time (up to 80 gsm
weight or 5.0 mm thickness). However, this is dependent upon the
stiffness of the paper.
Jog function is supported by the Main Stacker. Jogging and stapling
are mutually exclusive and cannot be selected simultaneously. When both
operations are selected, stapling overrides the jogging function.
Media Types Supported(1):
Tray Trays Aux. Opt. Main Main Upper
1 2,3 Tray HCF Stack. Stack. Stack.
Media Type (Staple)
---------------------- ---- ----- ---- ---- ----- ------- ------
Tab stock LEF (2) Yes Yes Yes No Yes Yes Yes
(9x11")
Letterhead (4) Yes Yes Yes Yes Yes Yes Yes
(Letter, A4)
Pre-printed (4) Yes Yes Yes Yes Yes Yes Yes
(Letter, A4)
Transparencies (2) (3) Yes Yes Yes Yes Yes No Yes
(Letter, A4)
Labels (2) (4) Yes Yes Yes Yes Yes Yes Yes
(Letter, A4)
Pre-punched paper (4) Yes Yes Yes Yes Yes Yes Yes
(Letter, A4)
Colored paper (4) Yes Yes Yes Yes Yes Yes Yes
(Letter, A4)
Note: (1) Some print media, although they may conform to size
and weight specifications, may not perform to your expectations. Print
quality, jam rates, fuser life, and output stacking can be affected by
the printing environment (temperature and humidity) and characteristics
of the paper (structure, moisture content, smoothness or thickness);
refer to IBM Document G544-3915 for general guideline specifications.
IBM STRONGLY RECOMMENDS YOU TEST SMALL AMOUNTS OF PRINT MEDIA USING
YOUR PRINTING APPLICATION BEFORE PURCHASING LARGE QUANTITIES OF THE
MEDIA OR RUNNING LARGE PRINT VOLUMES.
Note: (2) Duplex printing is not supported.
Note: (3) Using Auxiliary tray is recommended.
Note: (4) Letter or A4 size is required.
Operator Panel
Infoprint 70 has a simplified operator panel with scrolling
capability. It consists of 8 keys, 4 LED status indicators and a 2 x 20
character display. The scrolling of text messages offers enhanced
information for the operator.
The 8 keys consist of the following:
- Online - used to take printer online or offline.
- Enter - used to select an action item or menu item value.
- Menu (up/down) - used to scroll up or down through menus.
- Item (up/down) - used to scroll up or down through menu items listed in the message display area.
- Value (+/-) - used to scroll up or down through acceptable values for menu items.
The 4 LED Status Indicators are:
- Online - on when printer is online or idle, blinking when printer is receiving or processing data.
- Paper - on when paper tray is low or empty.
- Toner - on when toner supply is low.
- Attention - blinks when printer requires attention.
Printer status, intervention conditions, and menu items are displayed. Operator panel functions include:
- Print Quality (including density)
- Cancel current job being printed
- Offline Printouts
- AFP/IPDS font lists
- Network Configuration
- Printer Configuration
- Change language display
- Configure network protocols
Size and Weight
Unpacked size and weight are as follows:
Width Depth Height Weight
----- ----- ------ ------
Base (1) 650mm (25.6") 665mm (26.2") 1000mm (39.4") 180 kg (397 lb)
Finisher (2) 460mm (18.1") 616mm (24.3") 1035mm (40.7") 55 kg (121 lb)
784mm (30.9")including Tray
HCF (3) 400mm (15.7") 494mm (19.4") 465mm (18.3") 19 kg ( 42 lb)
" denotes inches
Note: (1) Print engine
Note: (2) Standard Finisher
Note: (3) Optional High Capacity Feeder
Acoustics
Sound Pressure
Standard configuration
Standby 53 dB(A)
Operating 63 dB(A)
Sound Power
Standard configuration
Standby 6.3 Bels(A)
Operating 7.3 Bels(A)
Electrical Specification
Infoprint 70 has only one model for worldwide:
Power Consumption and Thermal Output
Typical power consumption in Watts, British Thermal Units per Hour (BTU/HR) and Volt-Amperes (VA) are listed below.
Watts BTU/HR VA
------------ ------------ ------------
Power Saver Mode 39 133 55
Standby 560 1911 920
Printing 1560 5323 1955
Note: Infoprint 70 meets the EPA Energy Star specification of 45 Watts or lower.
Ozone Emissions
Infoprint 70 ozone emissions are less than 0.02 parts per million
(ppm) for an 8-hour Timed Weighted Average (TWA) limit. This is less
than the UL 1950 present recommended long term exposure limit for ozone
which is 0.1 ppm calculated as an 8-hour TWA concentration.
Agency Approvals
- US/Canada
- FCC part 15 Class A
- UL 1950 3nd Edition, by a National Recognized Test Lab (NRTL)
- CSA C22.2 #950-M95, 3rd Edition by a NRTL
- FDA 21 CRF Chapter 1, Subchapter J, Section 1010, 1040 (Laser Safety Requirement)
- CDRH Class 1 Laser Product
- Latin America
- NOM Voltage Compliance (Mexico)
- EMEA
- CB Report with all national deviations "TO EN 60950 WITH AMENDMENTS 1, 2, 3, AND 4"
- IEC950 2nd Edition, A1/A2/A3/A4 by a NTRL (VDE or TUV)
- IEC825 Class I Laser Product (Laser Safety Requirements)
- CE Mark (CE Directive)
- GS mark for Germany by VDE
- EN55022(CISPR Publication 22), Class A
- GOST FOR RUSSIA
- Japan
- VCCI Information Processing Equipment
- China
- CCIB (China) "CB REPORT MUST INCLUDE IBM AS APPLICANT AND THE IBM MODEL/TYPE"
- Taiwan EMC
- China EMC
Certifications
- U.S. Postal Barcode (PostNet)
- EuroReady
- Energy Star Compliance
Note: The Energy Star emblem does not represent EPA endorsement of any product or service.
Host Systems Supported
Infoprint 70 supports the following host systems:
- AS/400 Systems
- AS/400e Servers
- AS/400e Systems
- AS/400 Advanced Series
- RS/6000(R) systems
- Enterprise Servers
- Netfinity Servers
- S/390
- G5, G6 Parallel Enterprise Servers
- Multiprise Servers
- Integrated Servers
- ES/9000
Software
Physical Protocol Operating System
-------- -------- -----------------------------
LAN (IEEE 802.3/.5)
TCP/IP PSF/400 4.3, 4.4, 4.5
PSF/MVS 2.2
PSF for OS/390 3.1, 3.2
Infoprint Manager for AIX 3.2
Infoprint Manager for NT 1.1
PSF(TM)/MVS Support Summary
PSF/MVS PSF for OS/390
V2.2.0 V3.1.0,
V3.2.0
------- --------------
Base Support:
- 4028 Dev. Type Yes Yes
- Native(2770 Mode) Yes Yes
- 240 DPI Resolution Yes Yes
- 300 DPI Resolution Yes Yes
- Auto Resolution Yes Yes
(OPC will report LF1 240 or 300 DPI printer,
printer converts to 600 DPI)
Paper Input Yes Yes
(Tray 1, 2, 3, Aux.Tray and optional
High Capacity Feeder)
Paper Output
Main stacker, Upper stacker Yes Yes
Stapling Yes Yes
Jogging Yes Yes
AFP/IPDS Towers: All All
Printer Connectivity:
- Ethernet TCP/IP Yes Yes
- T/R TCP/IP Yes Yes
Font Download
- Outline Yes Yes
- Raster Yes Yes
Resident AFP Font Collection
- 4028 Yes Yes
- Core Yes Yes
- Coordinated Yes Yes
-DBCS Outline Yes Yes
-DBCS Raster Yes Yes
PSF/MVS Support Notes
- APAR OW27622 for PSF/MVS 2.2.0 is required for multi-resolution (auto) support.
- PSF/MVS 2.1.x is no longer supported or maintained by IBM.
- PSF/MVS 2.2.0 is withdrawn from marketing effective 3/31/99 and replaced by PSF V3.1.0 for OS/390
- APAR OW39102 for PSF for OS/390 or APAR OW38078 for PSF/MVS 2.2.0 is required for outline font support
PSF/400 Support Summary
PSF/400
V4R3, V4R4, V4R5
----------------
Base Support:
- 4028 Dev. Type Yes
- Native(2770 Mode) Yes
- 240 DPI Resolution Yes
- 300 DPI Resolution Yes
- Auto Resolution Yes (V4R3, V4R4, V4R5)
(OPC will report LF1 240 or 300 DPI printer,
printer converts to 600 DPI)
Paper Input Yes
(Tray 1, 2, 3, Aux.Tray and optional
High Capacity Feeder)
Paper Output
Main stacker, Upper stacker Yes
Stapling Yes
Jogging Yes
AFP/IPDS Towers: All
Printer Connectivity:
- Ethernet TCP/IP Yes
- T/R TCP/IP Yes
Font Download
- Outline Yes
- Raster Yes
Resident AFP Font Collection
- 4028 Yes
- Core Yes
- Coordinated Yes
-DBCS Outline Yes
-DBCS Raster Yes
Infoprint Manager Summary
Infoprint Infoprint
Manager for Manager
AIX V3.2 NT 1.1
----------- ---------
Base Support:
- 4028 Dev. Type Yes Yes
- Native(2770 Mode) Yes Yes
- 240 DPI Resolution Yes Yes
- 300 DPI Resolution Yes Yes
- Auto Resolution Yes Yes
(OPC will report LF1 240 or 300 DPI printer,
printer converts to 600 DPI)
Paper Input Yes Yes
(Tray 1, 2, 3, Aux.Tray and optional
High Capacity Feeder)
Paper Output
Main stacker, Upper stacker Yes Yes
Stapling Yes Yes
Jogging Yes Yes
AFP/IPDS Towers: All All
Printer Connectivity:
- Ethernet TCP/IP Yes Yes
- T/R TCP/IP Yes Yes
Font Download
- Outline Yes Yes
- Raster Yes Yes
Resident AFP Font Collection
- 4028 Yes Yes
- Core Yes Yes
- Coordinated Yes Yes
-DBCS Outline Yes Yes
-DBCS Raster Yes Yes
Printer Resident Web pages
The Infoprint 70 supports printer resident Web pages to view printer
and job status and to configure printer settings via a Web browser.
Printer Resident Web site
The Infoprint 70 includes printer resident Web pages. The Web pages
can be viewed by an industry standard browser using the printer IP
address. Public Web pages are available to all users. Administrator Web
pages are provided for configurator functions. Administrator Web pages
require password access. The type of Web pages include:
- Public Web pages, end user support and functions (available to anyone with URL or IP address).
- View printer status, job status and general printer parameters.
- Administrator support function (available to anyone with password protection).
- Configure printer and network interface using a Web browser. All operator panel functions are available via Web access.
- View printer status, job status and general printer parameters.
Infoprint 70 supports remote device management via a Web browser. Browsers supported include:
Browser Version
----------------- -------------
Netscape 4.0 and above
Internet Explorer 4.0 and above
AFP/IPDS
Infoprint 70 supports these AFP/IPDS functional enhancements:
- Media selection by object ID (supported by PSF/MVS 3.1.0, PPFA, PSF/400 V5R1)
- Dutch KIX postal bar code (supported by all PSFs and all Infoprint Managers)
- Australia Post bar code (supported by all PSFs and all Infoprint Managers)
- Printer identification by name.
- Outline font, 240 pel raster fonts and font resource capture (hard disk).
- Resolution independent raster font support.
- Japan Postal bar code support.
- Double Byte Character Set (DBCS) font support (resident and download)
- Partial Arc drawing order support.
- Box drawing order support.
In addition to the AFP/IPDS enhancements, Infoprint 70 provides a
Hard Disk Drive (HDD) standard with preloaded Double Byte Character Set
(DBCS) Outline Font Resources. This is a benefit to applications which
use double byte characters.
AFP/IPDS Limitations
Infoprint 70 has the following limitations on AFP/IPDS capabilities as compared to the 3130, 3160 and Infoprint 60 printers:
- Paper orientation (edge/size sensitivity) not configurable.
- N-up and explicit page placement/orientation not supported.
- Limited units of measure.
- Limited page segment and overlay activation (256).
- No overlay caching to disk (SDRAM only).
AFP/IPDS SBCS Resident Font Support
Printer resident fonts are supported using outline font technology.
Under native mode, all printer-resident AFP/IPDS fonts are accessible
to PSF.
- IBM 4028 Compatibility AFP/IPDS Resident Font Set (supported using outline font technology).
Typeface FGID Typeface FGID
--------------------- ---- ------------------------ -----
APL 76 Prestige Pica 10 Pitch 12
Boldface 159 Prestige Pica Bold 60
Courier 5 Pitch 244 Prestige Elite Bold 12 111
Courier 10 Pitch 11 Prestige Elite Italic 12 112
Courier 12 Pitch 85 Times Roman Typo 6 pt 5687
Courier 15 Pitch 223 Times Roman Typo 8 pt 5687
Courier 17.1 Pitch 252 Times Roman Typo 10 pt 5687
Courier 17.1 Pitch 254 Times Roman Typo 12 pt 5687
Courier Bold 10 Pitch 46 Times Roman Bold Typo 10 5707
Courier Bold 12 Pitch 108 Times Roman Bold Typo 12 5707
Courier Italic 10 18 Times Roman Bold Typo 14 5707
Courier Italic 12 92 Times Roman Bold Typo 18 5707
Gothic Text 13.3 Pitch 203 Times Roman Bold Typo 24 5707
Gothic Text 20 Pitch 283 Times Roman Ital. Typo 10 5815
Gothic Text 26.7 Pitch 290 Times Roman Ital. Typo 12 5815
Letter Gothic 20 281 Times Roman Bold Italic 5835
OCR A 19 Typo 10 pt
OCR B 03 Times Roman Bold Italic 5835
Prestige 12 Pitch 86 Typo 12 pt
Prestige (PSM) 164
Prestige Roman Bold 701
Prestige 15 Pitch 221
Prestige 17.1 Pitch 256
Note on 4028 Font Compatibility
Note: "Gothic Text" added to "391X" and "311X" printers
- IBM Core Interchange Resident Scalable Font Set
Typeface FGID
------------------------------------------- ----
Latin 1/2/3/4/5 with Euro (All GCSGID 1355)
Times New Roman** Medium 2308
Times New Roman Bold 2309
Times New Roman Italic Medium 2310
Times New Roman Italic Bold 2311
Helvetica** Roman Medium 2304
Helvetica Roman Bold 2305
Helvetica Italic Medium 2306
Helvetica Italic Bold 2307
Courier Roman Medium 416
Courier Roman Bold 420
Courier Italic Medium 424
Courier Italic Bold 428
Symbols (GCSGID - 1275)
Times New Roman Medium 2308
Times New Roman Bold 2309
Helvetica Roman Medium 2304
Helvetica Roman Bold 2305
Courier Roman Medium 416
Courier Roman Bold 420
Cyrillic Greek (GCSGID - 1300)
Times New Roman Medium 2308
Times New Roman Bold 2309
Times New Roman Italic Medium 2310
Times New Roman Italic Bold 2311
Helvetica Roman Medium 2304
Helvetica Roman Bold 2305
Helvetica Italic Medium 2306
Helvetica Italic Bold 2307
Courier Roman Medium 416
Courier Roman Bold 420
Courier Italic Medium 424
Courier Italic Bold 428
Arabic (GCSGID - 1264)
ITC Boutros Setting Medium 2308
ITC Boutros Setting Bold 2309
ITC Boutros Setting Italic Medium 2310
ITC Boutros Setting Italic Bold 2311
ITC Boutros Modern Rokaa Medium 2304
ITC Boutros Modern Rokaa Bold 2305
ITC Boutros Modern Rokaa Italic Medium 2306
ITC Boutros Modern Rokaa Italic Bold 2307
Boutros Typing Medium 416
Boutros Typing Bold 420
Boutros Typing Italic Medium 424
Boutros Typing Italic Bold 428
Hebrew (GCSGID - 1265)
Narkissim Medium 2308
Narkissim Bold 2309
Narkissim Italic Medium 2310
Narkissim Italic Bold 2311
Narkiss Tam Medium 2304
Narkiss Tam Bold 2305
Narkiss Tam Italic Medium 2306
Narkiss Tam Italic Bold 2307
Shalom Medium 416
Shalom Bold 420
Shalom Italic Medium 424
Shalom Italic Bold 428
IBM Coordinated Scalable Font Set
Typeface FGID GCSGID
-------- ---- -------
APL 307 1304
APL Bold 322 1304
Boldface 20224 2039
Gothic Text 304 2039
Letter Gothic 400 2039
Letter Gothic Bold 404 2039
OCR A 305 968
OCR B 306 969
Prestige 432 2039
Prestige Bold 318 2039
Prestige Italic 319 2039
Katakana Gothic 304 1306
AFP/IPDS Barcode Printing
-
To support the BCOCA tower for printing of bar codes, the OCR-A and
OCR-B fonts and their corresponding codes pages (892 and 893) must be
resident in the printer. These are supported as shown in the "4028
Compatibility AFP/IPDS Resident Font Set" table. Code page 1303 is also
resident to be used for 128 bar codes.
AFP/IPDS DBCS Resident Raster Font Support
The following AFP font products are available in resident form as
standard in Infoprint 70 printer. These fonts provide 240 pel
capability for Japanese, Korean, Simplified Chinese, Traditional
Chinese and Thai languages.
- AFP Japanese Object Font V2R1.1 for MVS (5771-AGB)
- AFP Japanese Object Font V2R1.0 for MVS (5771-AGB) Except for Section 68
- AFP Korean Object Font V1R1.1 and V1R1.0 for MVS (5771-AFW)
- AFP Traditional Chinese Object Font V1R1.2 and V1R1.1 for MVS (5771-AFZ)
- AFP Simplified Chinese Object Font V1R1.1 and V1R1.0 for MVS (5771-AEK)
- AFP Thai Object Font V1R1.1 and V1R1.0 for MVS (5771-AEN)
These fonts are only available in raster form at 240 pel.
Though AFP Japanese Font 5771-AGB consists of 23 sizes of DBCS
fonts and 20 sizes of SBCS fonts, the SBCS fonts are NOT available in
this resident raster font set.
EBCDIC Attachment Language Support
The language and associated code page support below is based on the
current SAA Core Interchange Resident Code Page Support and 4028
Compatibility Resident Code Page Set. Only EBCDIC code pages are
listed.
Language Code Page Character Set
-------- --------- -------------
APL (4028) CP310 963
APL (Exp. Core) CP293 380
Arabic Bilingual CP420 235
- GML List Symbols CP1039 1258
Austrian/German CP273 (1141)(3) 697 (695)(3)
- Publishing CP382 1145
- Alternate (4028) CP286 317
Belgian CP274 697
- Publishing CP383 1145
Brazilian CP275 697
Brazilian Portuguese CP037 (1140)(3) 697
- Publishing CP384 1145
Canadian French (4028) CP260 341
- Publishing CP385 1145
- DP94 (4028) CP276 277
Cyrillic/Multilingual CP880 960
- Primary CP1025 1150
- GML List Symbols CP1039 1258
Danish/Norwegian CP277 (1142)(3) 697 (695)(3)
- Publishing CP386 1145
- Alternate (4028) CP287 321
Dutch CP037 697
English (UK) CP285 (1146)(3) 697 (695)(3)
- Publishing CP394 1145
Finnish/Swedish CP278 (1143)(3) 697 (695)(3)
- Publishing CP387 1145
- Alternate (4028) CP288 325
French CP297 (1147)(3) 697 (695)(3)
- Publishing CP388 1145
Note: (3) Equivalent Euro Code Page
Greek 183 CP423 218
- Primary CP875 925
Hebrew (Israel) CP424 941
- Publishing CP1028 1199
- GML List Symbols CP1039 1258
- Char. Set A CP803 1147
Iceland CP871 (1149)(3) 697 (695)(3)
Italian CP280 (1144)(3) 697 (695)(3)
- Publishing CP389 1145
Japanese (English) CP281 697
- Publishing CP390 1145
- Katakana CP290 1172
- Katakana Extended CP1027 1172
Latin 2 Multilingual CP870 959
Latin 3 Multilingual CP905 1286
Latin 4 EBCDIC CP1069 1256
Latin 5 CP1026 1152
Latin DCF
- Rel. 2 Compat. CP1002 1132
- US Text Subset CP1003 1133
- Numeric Spacing CP1068 1259
- GML List Symbols CP1039 1258
Multilingual CP500 (1148)(3) 697 (695)(3)
- Publishing CP361 1145
OCR-A CP892 968
OCR-B CP893 969
Portuguese CP282 697
- Alternate CP037 697
- Publishing CP391 1145
Spanish CP284 (1145)(3) 697 (695)(3)
- Castillian CP392 1145
- Latin America CP393 1145
Symbols, Set 7 CP259 340
- Modified Set 7 CP1091 1191
- Set 8 CP363 630
- Math Symbols CP829 909
Symbols, Adobe CP1087 1257
Turkey (Latin 2) CP870 959
US/Canadian (English) CP037 (1140)(3) 697 (695)(3)
- Publishing CP395 1145
Note: (3) Equivalent Euro Code Page
PCL/PostScript Features (Optional)
Two PCL and Adobe PostScript features are now available. These features include:
- PCL 6 (XL) and 5e resident fonts - 51 fonts total
- Adobe PostScript 3 resident fonts - 136 fonts total
The PCL/PostScript Module (features 4820 and 4821) includes Single
Byte Character Set support. The PCL/PostScript Japanese Module
(features 4810 and 4811) includes Double Byte Character Set support.
Included are the Morisawa fonts. This feature should only be ordered if
double byte support is required.
Features 4820/4821 and 4810/4811 are mutually exclusive and only one
of them can be ordered. If the MES version is ordered (feature numbers
4821 or 4811) the existing hard drive will be replaced and the customer
needs to download resource fonts again to the new hard drive.
Attachments
Attachment/Operating System Support:
Physical Protocol Operating System(1)
--------- -------- ----------------------------------------------
LAN (IEEE 802.3/.5)
IPX/SPX Novell NetWare 3.1, 3.11, 3.12, 4.0, 4.01, 4.1,
5.0, 3.12J, 4.11J
TCP/IP Novell NetWare 5.0
Windows 95/98/Me, Windows NT 4.0, Windows 2000
AIX 4.1, and higher
OS/400 3.2, 4.1, 4.2, 4.3, 4.4, 4.5
NETBIOS/ Windows 95/98, NT 4.0, Windows 2000
NETBEUI
IBM OS/400 ASCII Printer Support
Infoprint 70 is supported as an ASCII(PCL) printer via a Workstation
Customization Object under the Host Print Transform (HPT) facility of
OS/400 V3.2 and higher.
HPT transforms the AFPDS data stream to ASCII data stream which can
be sent to this printer when attached directly to a Token-Ring or
Ethernet LAN via TCP/IP. That connection can use either of the
following two TCP/IP drivers:
- OS/400 SNMP printer driver
- OS/400 TCP/IP Line Printer Requester (LPR) and Line Printer Daemon (LPD), also known as remote output queue
HPT support (AFP to ASCII) includes the following limitations:
- AFP graphics (GOCA) commands not supported
- Multiple-up not supported
- Edge to edge not supported
- AFP to ASCII may need to be run in raster more in order to produce accurate results
PCL Font Support
The optional PCL/PostScript feature supports the PCL resident fonts, include the following:
- 49 PCL Outline Fonts:
- 4 CG Times*
- 4 Univers*
- 4 Univers Condensed
- 4 Courier
- 3 Letter Gothic
- 2 Albertus*
- 3 Antique Olive*
- 1 Clarendon Condensed
- 1 Coronet
- 4 Garamond
- 4 Helvetica(1)
- 1 Marigold*
- 4 CG Omega*
- 4 Arial
- 4 Times New
- 1 Symbol
- 1 Wingdings*
- PCL Bitmapped Fonts:
- LinePrinter 16.7 pitch, 8.5 Pt (Portrait)
- LinePrinter 16.7 pitch, 8.5 Pt (Landscape)
Note: (1) Only available in a limited set of symbol sets.
PCL fonts are not accessible via AFP/IPDS, nor can PCL access AFP/IPDS fonts.
PCL Symbols Set Support
This feature supports the following PCL Symbol sets:
Name Abreviation ID
--------------- ----------- --
Desktop Desktop 7J
Hebrew 7-bit(1) 0H
ISO 11 Swedish ISO11 OS
ISO 15 Italian ISO15 O1
ISO 17 Spanish ISO17 2S
ISO 21 German ISO21 1G
ISO 4 UK ISO4 1E
ISO 60 Danish/Norwegian ISO60 OD
ISO 69 French ISO69 1F
ISO 6 ASCII ISO6 OU
ISO 8859/1 Latin 1 ISOL1 ON
ISO 8859/2 Latin 2 ISOL2 2N
ISO 8859/5 Latin/Cyrillic(1) 10N
ISO 8859/6 Latin/Arabic(1) 11N
ISO 8859/7 Latin/Greek(1) 12N
ISO 8859/8 Latin/Hebrew(1) 7H
ISO 8859/9 Latin 5 ISOL5 5N
ISO 8859/10 Latin 6 ISOL6 6N
Legal LEGAL 1U
Math-8 MATH8 8M
MC Text MCText 12J
Microsoft Publishing MSPUB 6J
PC-1004 PC1004 9J
PC-775 PC775 26U
PC-850 (euro) PC850 12U
PC-852 PC852 17U
PC-855 Latin/Cyrillic(1) 10R
PC-858 (euro) PC858 13U
PC-862 Latin/Hebrew(1) 15H
PC-864 Latin/Arabic(1) 10V
PC-866 Cyrillic-Russia(1) 3R
PC-869 Latin/Greek(1) 11G
PC-8 D/N PC8DN 11U
PC-8 Turkish PC8TK 9T
PC-8 Multilingual Code Page 437 PC8 10U
Pi Font PIFONT 15U
PS Math PSMATH 5M
PS Text PSText 10J
Roman-8 Roman 8U
Ventura International VNINTL 13J
Ventura Math VNMATH 6M
Ventura US VNUS 14J
Windows 3.0 Latin 1 WIN30 9U
Windows Baltic WINBALT 19L
Wingdings WINGDINGS 579L
Windows 3.1 Latin 1 (Euro) WINL1 19U
Windows 3.1 Latin 2 (Euro) WINL2 9E
Windows 3.1 Latin 5 (Euro) WINL5 5T
Note: (1) Only available in Courier, Helvetica and Times New Roman typefaces.
Adobe PostScript Character Set Support
Character Set Encoding Vector
------------- ---------------
ISOAdobe ISOLatin1
PostScript Font Support
The optional PCL/PostScript Modules supports the Adobe PostScript 3 fonts including the following 136 fonts:
Typeface # of Fonts Typeface # of Fonts
------------ ---------- -------- ----------
Albertus 3 Marigold 1
AntiqueOlive 4 Monaco 1
Apple Chancery 1 MonaLisa-Recut 1
ArialMT 4 NewCenturySchlbk 4
AvantGarde 4 NewYork 1
Bodoni 6 Optima 4
Bookman 4 Oxford 1
Carta 1 Palatino 4
Chicago 1 StempelGaramond 4
Clarendon 3 Symbol 1
CooperBlack 2 Tekton 1
Copperplate 2 Times 4
Coronet 1 TimesNewRomanPS 4
Courier 4 Univers 14
GillSans 9 Wingdings 1
Eurostile 4 ZapfChancery 1
Geneva 1 Zapfdingbats 1
Goudy 5
Helvetica 8
Helvetica Narrow 4
HoeflerText 5
JoannaMT 4
LetterGothic 4
LubalinGraph 4
PostScript fonts are not accessible via AFP/IPDS, nor can PostScript access AFP/IPDS fonts.
The following Adobe PostScript 3 resident Japanese DBCS fonts are supported with feature numbers 4810/4811.
- Japanese Morisawa fonts:
- FutoGoB101-Bold
- FutoMinA101-Bold
- GothicBBB-Medium
- Jun101-Light
- Ryumin-Light
Printer Drivers
The following drivers are available for PCL/PostScript:
Languages
Data ---------
Platform Stream EN FR IT GR SP BP DU JP SC TC RUS PO HU
---------------- --------- -- -- -- -- -- -- -- -- -- -- --- -- --
Windows 95/98/Me PCL 5e X X X X X X X X X X X X X
Windows 95/98/Me PCL 6 X X X X X X X X X X X X X
Windows 95/98/Me PS 3 X X X X X X X X
Windows NT 4.0 PCL 5e X X X X X X X X X X X X X
Windows NT 4.0 PCL 6 X X X X X X X X X X X X X
Windows NT 4.0 PS 3 X X X X X X X X
Windows 2000 PCL 5e X X X X X X X X X X X X X
Windows 2000 PCL 6 X X X X X X X X X X X X X
Windows 2000 PS 3 X X X X X X X X
AIX 4.2 - 4.xx PS 2 X X X X X X
Languages: EN=English SP=Spanish SC=Simplified Chinese
FR=French BP=Brazilian Portuguese TC=Traditional Chinese
IT=Italian DU=Dutch RUS=Russian
GR=German JP=Japan PO=Polish
HU=Hungarian
Printer Utilities
Network Printer Resource Utility (NPRU)
Network Printer Resource Utility (NPRU) is an application that
provides a repository (resource inventory) for fonts and overlays
(macros) on a workstation with access to an IBM network printer. Once a
font or overlay has been added to the NPRU inventory, it can be
downloaded to RAM or hard drive.
The font formats supported are PCL Intellifonts, TrueType, and
PostScript Type-1. Fonts and overlays that are downloaded are available
to workstation applications when the network printer drivers are
selected. NPRU is a separate program that uses the printer drivers to
download. It is supported for:
Operating System Data Stream
---------------- -----------
Windows 95/98/Me PCL 5e
Some drivers offer font and overlay download capability in the
driver. See table below. The font format supported is PostScript Type
1. Fonts and overlays that are downloaded are available to workstation
applications when the network printer drivers are selected. NPRU is a
separate program that uses the printer drivers to download.
Operating System Data Stream
---------------- --------------------------
AIX 4.1 and higher PostScript 2(1)
Note: (1) Download of truetype fonts is not currently supported.
NPRU is shipped with the printer on CD-ROM, but to get the most
current version see the IBM Printing Systems Company Home Page at:
-
http://www.ibm.com/printers.
IBM Network Printer Manager (NPM) for Windows Utility
IBM provides the Network Printer Manager (NPM) Utility with an easy-
to-use graphical interface for network administrators. Infoprint 70 is
supported on NPM version 4.21. NPM runs on Microsoft Windows
95/98/Me/NT 4.0 and Windows 2000 platforms.
Network administrators can setup e-mail or pager notifications for
Infoprint 70. Whether printers are low on toner, out of paper, or need
attention, these notifications can get the information to the right
source without delay, improving printer up-time and end user
productivity.
NPM helps users install and configure IBM network printers in LANs,
including Novell networks (Bindery and NDS). NPM monitors printers and
provides printer status using the industry-standard, open-systems SNMP
(Simple Network Management Protocol) Printer MIB and private enterprise
MIBs.
Some examples of the information available using SNMP are as follows:
- On/offline
- Paper jam
- Out of toner
- Output tray full
- Input tray empty
- Information about the printer's configuration
- Capacity
- Information about number of pages printed
Other functions provided by NPM include:
- Printer microcode update
- Printer grouping
- Printer reset
- Copy printer settings
NPM uses the following protocols:
Client Operating Control Configurable
Systems Protocols Protocols
------------------------ --------------- ------------------------
Windows 95/98/Me/NT 4.0 TCP/IP, IPX/SPX TCP/IP, IPX/SPX, NetBios
Windows 2000
TCP/IP Network Port Monitor Utility
The IBM TCP/IP Network Port Monitor provides bi-directional printer
and job status for the Infoprint 70. It runs on Windows NT 4.0 and
Windows 2000 print servers. Clients on the following systems can
benefit from the port monitor if they use a printer that was defined on
a Windows NT 4.0 machine and is shared to the network:
- Windows 95/98/Me
- Windows NT 4.0
- Windows 2000
Some of the benefits of the TCP/IP Network Port Monitor are as follows:
- Integrates with standard Windows printer objects
- Displays printer status
- Indicates that a job has completed printing and is ready for pickup
- Detailed progress of a job on the printer (such as "printing page 3 of 7" or "copy 2 of 5")
- Cancel print jobs on the actual printer and not just your workstation
LPR Remote Printing Client
The LPR Remote Printing Client utility provides a TCP/IP port
monitor for seamless Windows 95/98/Me network printing. This port
monitor can be used on Windows 95/98 to direct print jobs from Windows
applications to IBM Workgroup printers. This utility supports other
printers or print servers that run a TCP/IP LPD print server. The port
monitor can be used on mobile systems for remote printing or it can be
used on department print servers in an unattended print server mode.
This package also includes a command line LPR executable program for
printing jobs directly. The LPR program, called IBMLPR.EXE, provides a
standard RFC 1179 compliant printing interface and allows the -S and -P
parameters to be set by way of environment variables so that drag and
drop printing can be enabled for a default printer.
Web Ready Printing
Using a Browser To Submit Print Jobs
Two methods of submitting a print job to the printer are available
with Infoprint 70. They are referred to as (pull) and (push) printing.
For reference, the conventional method of job submission from a
workstation is to select File and Print from an application menu. This
process uses a print driver to create a print job which is then sent
from the local workstation to the printer. Depending upon the
installation configuration, the job may be sent directly to the
printer, or to a print server and then to the printer.
Pull Printing
With pull printing, a browser is used to access a web page in the
printer. The user fills in an entry field on the web page with an
internet address (or URL) of an existing file to be printed. An example
would be a tax form that is available from a government web site. After
entering the URL of the file, the user clicks on the Submit button.
This submits the URL to the printer. The printer then retrieves and
processes the file from the remote server identified by the URL. The
file is transferred over the network only once (from the remote server
to the printer). Conventional printing of a remote file requires the
transfer of the file over the network twice (from the remote server to
the local workstation and then to the printer).
Files printed using Pull Printing must be in the correct format to
be successfully processed. Supported formats include the following:
- Postscript
- PDF
- PCL (6 and 5e)
- PJL
- Microcode update
Supported transfer protocols include HTTP, FTP and Gopher via a
proxy server. In order for the printer to reach a server that is on the
other side of a firewall, the proxy server must provide access through
the firewall. The address of the proxy server is a configuration item
in the printer that can be set by the printer administrator.
Pull printing provides a one step method of printing existing
documents or forms that are available on many web sites. Pull printing
can also be used to update the microcode of a printer by entering the
URL of the microcode update file. The microcode file can be retrieved
over the internet from the IBM Printing Systems web site
(www.ibm.com/printers) or from a server configured by the printer
administrator.
Push Printing
Push printing also uses a browser to submit a print job. As with
Pull Print, the user fills in an entry field on the web page that
identifies the name of an existing file to be printed. For push
printing, the identified file must be accessible as a local file to the
workstation. After entering the name of the file, the user clicks the
submit button. The browser reads the file and transfers it to the
printer. As with Pull Print, the file must be in a supported format,
including the following:
- PostScript
- PDF
- PCL
- PJL
- ASCII text
- Microcode update
Push printing provides a simple method of printing an existing document on any printer that can be reached with a browser.
IPP
IPP (Internet Printing Protocol) was commissioned by the Internet
Engineering Task Force (IETF) and developed under the guidance of the
Printer Working Group printing industry consortium. As such, IPP is
better defined than its LPR predecessor (RFC 1179) and is now being
adopted as a new standard for printing and job control in networks and
over the Internet.
Infoprint 70 includes an IPP server that can accept jobs from an IPP
client using HTTP/1.1 as the transport protocol as defined in IPPv1.0.
An IPPv1.0 client is required on any operating system from which you
want to do IPP printing. For example, Infoprint 70 can accept jobs
submitted using IPP from the IPP client for Windows NT. IBM provides
IPP clients for the following software solutions:
- IBM Infoprint Manager for Windows NT and Windows 2000
- Infoprint Server feature of OS/390 V2R8
A list of additional third party IPP clients is available from the Printer Working Group Web site at the following:
-
http://www.pwg.org.
Printer Management
SNMP MIB Support
Infoprint 70 supports industry standard open-systems SNMP printer MIBs.
- Printer MIB (RFC 1759):
- MIB II (MIB RFC 1213)
- Host Resources MIB (MIB RFC 1514)
- Job MIB (based on RFC 2707)
Novell NetWare Support
Novell NetWare connectivity is supported via Token-Ring and Ethernet Adapters as PSERVER or RPRINTER.
Spooling
With a standard hard disk, incoming print jobs can be spooled onto
the hard disk if the printer is busy. Other types of jobs, such as PDF
files, must be spooled because they cannot start printing until the
entire job is received. Other types of jobs (PostScript, PCL) can
either be sent directly to the printer or be spooled on the hard disk.
Some types of jobs, such as AFP/IPDS files, cannot be spooled because
they require communication back to the transmitting host concerning
their print status.
Infoprint 70 allows the administrator to customize the printer so
that all but AFP/IPDS jobs are spooled to the hard disk before
printing. In some cases, this can reduce network traffic by minimizing
the number of attempts to resend a job to a busy printer. The default
spooling setting is to spool all but AFP/IPDS jobs. The setting can be
changed on the operator panel or from the printer's Web page.
PCL Symbols Set Support
Infoprint 70 supports the following PCL Symbol sets:
Name Abbreviation ID
--------------------- ----------- ----
Desktop Desktop 7J
ISO 11 Swedish ISO11 OS
ISO 15 Italian ISO15 O1
ISO 17 Spanish ISO17 2S
ISO 21 German ISO21 1G
ISO 4 UK ISO4 1E
ISO 60 Danish/Norwegian ISO60 OD
ISO 69 French ISO69 1F
ISO 6 ASCII ISO6 OU
ISO 8859/1 Latin 1 ISOL1 ON
ISO 8859/2 Latin 2 ISOL2 2N
ISO 8859/9 Latin 5 ISOL5 5N
ISO 8859/10 Latin 6 ISOL6 6N
Legal LEGAL 1U
Math-8 MATH8 8M
MC Text MCText 12J
Microsoft Publishing MSPUB 6J
PC-1004 PC1004 9J
PC-775 PC775 26U
PC-850 (euro) PC850 12U
PC-852 PC852 17U
PC-858 (euro) PC858 13U
PC-8 D/N PC8DN 11U
PC-8 Turkish PC8TK 9T
PC-8 Multilingual Code Page 437 PC8 10U
Pi Font PIFONT 15U
PS Math PSMATH 5M
PS Text PSText 10J
Roman-8 Roman 8U
Ventura International VNINTL 13J
Ventura Math VNMATH 6M
Ventura US VNUS 14J
Windows 3.0 Latin 1 WIN30 9U
Windows Baltic WINBALT 19L
Wingdings WINGDINGS 579L
Windows 3.1 Latin 1 (Euro) WINL1 19U
Windows 3.1 Latin 2 (Euro) WINL2 9E
Windows 3.1 Latin 5 (Euro) WINL5 5T
Adobe PostScript Character Set Support
Character Set Encoding Vector
------------- ---------------
ISOAdobe ISOLatin1
World Trade Considerations
Printer Resident Font Support
AFP/
PCL PS IPDS
--- -- ----
Group 1 Languages
Japanese DBCS No Yes Yes
German Yes Yes Yes
French Yes Yes Yes
Simp. Chin.(DBCS) No No Yes
Italian Yes Yes Yes
Spanish Yes Yes Yes
Brazilian Portug. Yes Yes Yes
Trad. Chin.(DBCS) No No Yes
Korean No No Yes
U.S. English Yes Yes Yes
Group 2 Languages
Danish Yes Yes Yes
Dutch Yes Yes Yes
Swedish Yes Yes Yes
Finnish (1) Yes Yes
Arabic (L6) Yes No Yes
Norwegian Yes Yes Yes
Portuguese (1) Yes Yes
Russian (L5) No No Yes
Hebrew (L8) Yes No Yes
Thai No No No
Polish (L2) Yes No(2) Yes
Turkish Yes No(2) Yes
Czech (L2) Yes No(2) Yes
Hungarian (L2) Yes No(2) Yes
Greek Yes No Yes
Group 3
Albanian (L1) No Yes Yes
Bulgarian (L5) Yes No Yes
Byelorussian (L5) No No Yes
Catalan (L1) Yes Yes Yes
Croatian (L2) Yes No(2) Yes
Estonian (L4) No No(2) Yes
Farsi (L6) No No No
Icelandic (1) Yes Yes
Latvian (L4) No No(2) Yes
Lithuanian (L4) No No(2) Yes
Macedonian (L5) Yes No Yes
Romanian (L2) Yes No(2) Yes
Serbian (L5) Yes No Yes
Slovakian (L2) No No(2) Yes
Slovenian (L2) Yes No(2) Yes
Ukranian (L5) No No Yes
Urdu (L8) No No No
Vietnamese No No No
Laotian No No No
Group 1D Languages
Australian English (1) Yes Yes
Belgian English (1) Yes Yes
UK English (1) Yes Yes
English Uppercase Yes Yes Yes
S. African English (1) Yes Yes
Belgium French (1) Yes Yes
Canadian French (1) Yes Yes
Swiss French (1) Yes Yes
Swiss Italian (1) Yes Yes
Group 2D Languages
Belgium Dutch (1) Yes Yes
Note: (1) Supported via ISO Latin 1.
Note: (2) We do not support ISOAdobeCE.
Publications Languages
Language Availability(1)
-------------------- ---------------
Brazilian Portuguese GA
Danish GA
Dutch GA
English GA
Finnish GA
French GA
German GA
Hungarian GA
Italian GA
Japanese (Kanji) GA
Norwegian GA
Polish GA
Spanish GA
Swedish GA
Simplified Chinese GA
Traditional Chinese GA
Note: (1) Translated publications availability is based on country translation center commitment dates received from TPS.
Operator Panel Message Languages
Language(1) Availability
-------------------- ------------
Brazilian Portuguese GA
Danish GA
Dutch GA
English GA
Finnish GA
French GA
German GA
Hungarian GA
Italian GA
Japanese - Katakana GA
Norwegian GA
Polish GA
Spanish GA
Swedish GA
Note: (1) The operator panel template is translated into all the languages listed here.
Web Page Languages
The translations will be limited to user web pages only.
Language Availability
-------------------- ------------
Brazilian Portuguese GA
Danish GA
Dutch GA
English GA
Finnish GA
French GA
German GA
Hungarian GA
Italian GA
Norwegian GA
Polish GA
Spanish GA
Swedish GA
Japanese GA
Network Printer Manager (NPM) Languages
Language Availability
-------- ------------
English GA
TCP/IP Network Port Monitor Languages
Language Availability
-------- ------------
English GA
Brazilian Portuguese GA
French GA
Dutch GA
German GA
Hungarian GA
Italian GA
Polish GA
Russian GA
Spanish GA
Simplified Chinese (DBCS) GA
Traditional Chinese (DBCS) GA
Japanese GA
LPR Languages
Translation will be available in English only.
NPRU (Network Printer Resource Utility)
Windows
95/98/Me (PCL)
-------------
SBCS Languages
English X
Br. Portuguese X
Dutch X
French X
German X
Italian X
Spanish X
DBCS Languages
Simp. Chinese X
Trad. Chinese X
Japanese (Kanji) X
Network Printer Manager (NPM)
Windows
Language 95/98/Me/NT
-------- -----------
English X
TCP/IP Network Port Monitor Utility
Windows NT 4.0/
Language Windows 2000
---------------------------- ---------------
English X
Brazilian Portuguese X
French X
Dutch X
German X
Hungarian X
Italian X
Polish X
Russian X
Spanish X
Simplified Chinese (DBCS) X
Traditional Chinese (DBCS) X
Japanese X
Packaging
Number
Product Description of Boxes
--------------------- ------------------------------- --------
70 PPM Printer (220V) Base printer with control unit, 1
multi-language op-panel overlay,
safety/warranty info,
publications CD-ROM, utilities CD-ROM,
power cord, and language group which
contains User's guide (U.S. and Canada)
and Quick Reference Card
Power cord based on country code.
Language groups based on country
code unless specified.
High Capacity Feeder High Capacity Feeder, install sheet 1
IBM Token-Ring 4/16 Token-Ring card, Configuration Guide, 1
Adapter CD-ROM, install sheet
IBM Ethernet 10/100 Ethernet card, Configuration Guide, 1
Adapter CD-ROM, install sheet
PCL/PostScript Module PCL/PostScript Module 1
PCL/PostScript Japanese PCL/PostScript Japanese Module 1
Module
Toner Toner, install sheet 1
Staple cartridge Staple cartridge, install sheet 1
Drum unit Drum unit, install sheet 1
Fuser cleaning web Fuser cleaning web, install sheet 1
Language Groups User's Guide (U.S. and Canada), 1
Quick Reference Card
Line Cords Line cord 1
Operating Temperature: 50 to 90 deg F (10 to 32 deg C)
Humidity: 20 to 80% RH; 26 deg C max wet bulb
Altitude: 0-7,000 ft (0-2,133 m)
Storage:
Temperature: 14 to 104 deg F (-10 to 40 deg C)
Humidity: 5 to 90% RH
Shipping:
Temperature: -13 to 122 deg F (-25 to 50 deg C)
Humidity: 5 to 100% RH
 |
| Publications |
 |
Publication Order
Description Number
----------------------------------------------- ---------
User's Guide (U.S. and Canada only) SA18-7727
Safety Information GA18-7741
Quick Reference Card see below
Introduction & Planning Guide GA18-7726
Ethernet/Token-Ring Configuration Guide(1) S544-5711
Special Feature Codes -- Chargeable Factory Field
Mach Model Feature Feature
Type Number Number Description
---- ----- ------- ------- --------------------------------------
2770 001 70 PPM Printer
Mandatory feature (Only one of the two
below)
4120 4121 IBM Token-Ring 4/16 Adapter
4162 4163 IBM Ethernet 10/100 BaseTX Adapter
Optional features
4520 4521 High Capacity Feeder
4390 4391 128 MB Memory DIMM
4820 4821 PCL/PostScript Module
4810 4811 PCL/PostScript Japanese Module
Language Groups (includes printed Quick
Reference Card)
2924 English Language Group
(includes printed User's Guide)
2928 French Language Group
2980 Brazilian Portug. Language
2931 Spanish Language Group
2993 Danish Language Group
2988 Dutch Language Group
2987 Finnish Language Group
2929 German Language Group
2932 Italian Language Group
2920 Norwegian Language Group
2994 Swedish Language Group
2933 Polish Language Group
2934 Hungarian Language Group
2996 Chinese (S-C) Language Group
2995 Chinese (T-C) Language Group
2930 Japanese Language Group
9251 US, Canada, Japan Power Cord
9971 EMEA Power Cord
9979 Australia, New Zealand, Bolivia, Chile,
Peru, Uruguay Power Cord
9250 Chicago Power Cord
(#4120, #4121) Token-Ring Adapter
The Token-Ring feature is an internal adapter that plugs into the
controller. The adapter supports 4/16 Mbps Token-Ring. A maximum of one
Ethernet or Token-Ring feature may be ordered per printer.
(#4162, #4163) Fast Ethernet Adapter
The fast ethernet feature is an internal adapter that plugs into the
controller. The adapter supports 10/100BaseTX via a RJ-45 jack. A
maximum of one Ethernet or Token-Ring feature may be ordered per
printer.
(#4390) 128 MB Memory DIMM
The Infoprint 70 controller has 128 MB of memory on the controller
as standard. One additional 128 MB memory DIMM may be installed.
(#4520, #4521) High Capacity Feeder
This feature adds an additional input drawer with a capacity of
3,000-sheets. Only letter or A4 paper sizes are supported. A maximum of
one of these features may be ordered per printer.
(R), (TM), * Trademark or registered trademark of International Business Machines Corporation.
** Company, product, or service name may be a trademark or service mark of others.
